Машина для измельчения пластиковых отходов

Измельчитель для пластмассовых отходов предназначен для дробления PP, PE, LDPE, PVC, PET, HDPE, ABS и других мягких или твердых пластмасс. В этой статье основное внимание уделяется принципу работы, структуре, применению, параметрам и преимуществам измельчителя для пластмассовых отходов....
Измельчитель для отходов пластика
4.8

Дробилка для пластиковых отходов предназначена для измельчения ПП, ПЭ, ПЭНП, ПВХ, ПЭТ, ПЭВП, АБС и других мягких или твердых пластиковых отходов. Такие как пластиковые пленки, пластиковые бутылки, трубы ПВХ, трубы PE и т. д.

Изменяя сетку с разными диаметрами отверстий, можно получить частицы разного размера.

Различные модели измельчителей для пластиковых отходов

Introduction of Waste Plastic Crusher

A plastic waste shredder machine is a recycling equipment that specializes in crushing waste materials into pieces, which is widely used in the industries of plastic recycling, regeneration and granulation, waste products processing, and environmental protection resource utilization.

It crushes scraps by cutting and shredding them into small flakes through the high-speed rotating blades. This step is convenient for subsequent cleaning, melting, extruding, and pelletizing.

Дробильная машина является важной частью оборудования в линии гранулирования пластика, что существенно повышает эффективность производства.

Plastic Crushing Machine Principle

Рабочий принцип измельчителя для переработки пластика заключается в том, что подвижное лезвие вращается с высокой скоростью, сотрудничая с неподвижным лезвием для резки больших кусков пластика. Затем материал проходит через сетку и выводится.

Structure of Shredder Machine

Машина для измельчения пластмассы главным образом состоит из загрузочного бункера, измельчающей камеры, ножевой рамы, сетчатой пластины, нижнего бункера, двигателя и т. д. Дробильная камера пластиковой дробильной машины служит местом разрушения материала. В дробильной камере находятся подвижные лезвия, неподвижные лезвия, сетки и другие аксессуары.

Дробильная камера дробильной машины служит местом дробления материала. В камере дробления имеются подвижные и фиксированные лезвия, сита и другие аксессуары.

Plastic Grinding Machine Application

Industrial grinder machine can crush HDPE, LDPE, LLDPE, ДОМАШНИЙ ПИТОМЕЦ, PVC, ABS, etc., like buckets, baskets, trays, straws, irrigation pipes, auto bumpers, фильм, shopping bags, волокнистые мешки, electronic meters, bubble wrap, cosmetic tubes, bag cut-offs, agricultural films and other plastic scraps.

Пластиковая бочка

Industrial Plastic Shredder Parameters

МодельSL-80500 кг/ч
Производительность1 т/чмощность
15+7.5 Вт30+11 кВтДва горячих модельных параметра измельчителя для пластмассовых отходов
Простая конструкция, небольшой объем, легкий вес, низкое энергопотребление на единицу продукта
дробилку для пластика
дробилку для пластика

Waste Plastic Crusher Working Process

Step 1:Feeding

The waste plastics (such as bottles, films, woven bags, pipes, etc.) are fed into the crushing chamber of the waste plastic crusher through the inlet or conveyor belt. Some models are equipped with a pressure device to prevent the material from rebounding.

Step 2:Crushing

The crushing chamber of the waste plastic crusher is equipped with a set of rotating knives (movable knives) and fixed knives. When the plastic enters the area of the blades, a strong shearing and tearing effect is formed between the movable knife and the fixed knife, thus breaking the plastic material into small pieces.

  • The movable knife rotates with the knife shaft at high speed.
  • The fixed knife is fixed in the knife frame or side wall.

Step 3:Sizing

The crushed material falls to the screen structure (sieve plate) at the bottom of the machine, and only the crushed material with a particle size smaller than the sieve hole can pass through.

  • Only material with a particle size smaller than the holes in the sieve passes through. Material with a particle size too large for the sieve continues to be crushed.
  • The screen can be replaced to control the size of the material to be discharged.
Рабочий процесс шлифовальной машины

Notes on Waste Plastic Crusher Shredder Machine

  1. Regularly check the bearings and replace the high-speed grease to ensure the normal operation of the industrial shredder.
  2. After work, the shredder machine must be cleaned of all parts of residual materials.
  3. Если при использовании дробилки обнаруживается, что скорость шпинделя постепенно снижается, двигатель необходимо отрегулировать вниз, чтобы машина могла достичь заданной скорости, а любые обнаруженные отклонения следует остановить для проверки.
  4. строго запрещается впускать в машину металлические материалы, такие как гвозди, железо и т. д. дробилку для пластика включен, попадание в машину металлических материалов, таких как гвозди, железо и т. д., строго запрещено.
  5. Подачу материала следует постепенно увеличивать, наблюдая потребляемую мощность и работу двигателя.
  6. Рабочий процесс пластиковой дробильной машины
Waste plastic crusher for sale
Waste plastic crusher for sale

Advantages of Plastic Recycling Shredder

  • Передняя и задняя стенки дробильной камеры выполнены с двойным звукоизоляцией, низкий уровень шума
  • The front and rear walls of the crushing chamber adopt double-layer sound insulation, and low-noise
  • Smooth movement, low vibration, easy operation
  • Сильная силовая резка, высокая производительность, большое соотношение измельчения, равномерный размер фрагмента
  • Отдельная загрузочная воронка, дробильная камера и сортировочная воронка, легкость загрузки и разгрузки
  • The special design of the crushing chamber, no hopper, large inlet, and easy to load
  • Дробленые углы можно направить прямо на экструдер

FAQs of Plastic Shredder Machine for Recycling

How does a plastic shredder machine for the recycling process of plastic bottles, films, and woven bags?

Plastic bottles, films, and woven bags can be fed directly into the shredder machine, where the machine’s blades will cut them into smaller particles or fragments by shearing. For larger or harder materials, pre-processing is recommended (e.g. foam compressor).

What size materials can the Waste plastic crusher handle?

Different models of Waste plastic crushers can handle different sizes of materials. Generally speaking, the inlet size, blade design, and power of the machine will affect the processing capacity. You need to choose the right model according to the actual demand.

How often do I need to change the blades of my plastic shredder?

The frequency of blade replacement depends on the usage, the hardness of the material being processed and the blade material. In general, if the blades are worn or not sharp, they should be replaced promptly.

Запрос

Для получения информации о цене, мощности и модели дробилки оставьте сообщение на сайте. Мы вышлем вам подробное коммерческое предложение и каталог.